{"product_id":"ap-racing-j-hook-competition-spline-drive-disc-replacement-ring-380x32mm-right-hand","title":"AP Racing J Hook Competition Spline Drive Disc Replacement Ring (380x32mm)- Right Hand","description":"\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/spline_drive_disc_ring_inboard_angle_1201.jpg\" alt=\"spline_drive_disc_ring_inboard_angle_1201.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eAP Racing J Hook discs are the epitome of endurance\r\n racing components.  They will hold up extremely well to any abuse you \r\nplan to throw at them. These discs have been proven time and again in \r\nprofessional racing, winning many races and even championships (ALMS, \r\nRolex, Grand Am, etc.)\r\n\u003c\/p\u003e\u003ch3\u003eTwo-piece Floating Design with Aluminum Hat \u003c\/h3\u003e\u003cp\u003eAs\r\n is the case with most metal, iron brake discs grow substantially when \r\nheated.  As it is heated, a disc expands radially, increasing in \r\ndiameter and circumference.  One-piece disc designs run into problems \r\nwhen this occurs.   Look at the picture below and imagine the disc is \r\nbeing heated on the track.  As the disc expands, the outer edges of the \r\ndisc are pulling away from the center of the disc, but there are no \r\nbuilt-in provisions to allow for that expansion.  The edges of the disc \r\ntherefore pull, lift, and distort, which is called coning.  Now imagine \r\nthat disc vertical on the car, running in your caliper.  Coning directly\r\n impacts the brake pads’ contact with the disc, leading to uneven wear \r\nand tapering, and even a long brake pedal.\r\n\u003c\/p\u003e\u003cp\u003eTwo-piece discs on the other hand, compensate for the expansion of the disc as it heats. This is accomplished by building ‘float’ into the 2-piece disc assembly, allowing the disc to run true inside the caliper and reducing distortion, stress cracks, and pad taper. Traditionally, this float was built into \u003ci\u003eeither\u003c\/i\u003e the disc itself or the disc hat\/bell. This is commonly referred to as a disc’s ‘attachment method’, ‘mounting system’, or ‘drive system’. On a float-in-disc assembly, the iron disc ring has an oblong hole or channel in which a stainless steel bobbin slides as the disc heats and expands (Figure A below).In a float-in-hat assembly, the disc bobbin slides in a channel cut into the aluminum hat (Figure B below).With both disc drive methods, the iron disc ring typically has 10-12 mounting tabs cast into its outer face to which the aluminum hat is bolted (Figure C below).On an assembled disc being run in competition, those mounting tabs are responsible for completely bearing the load being placed on the disc.\r\n\u003c\/p\u003e\u003cp\u003eFigure A: Float-in-disc attachment method\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/disc_float_hot_web_4.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eFigure B: Float-in-hat attachment method\u003co:p\u003e\u003c\/o:p\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/float_in_hat_attachment_1200.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eFigure C: Traditional bobbin drive mounting tabs\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/disc_ring_mounting_tab_arrows.jpeg\"\u003e\r\n\u003c\/p\u003e\u003ch2\u003eNew Spline Drive Attachment Method\u003c\/h2\u003e\u003cp\u003eThe Essex Spline Drive mounting system uses the latest technology from professional racing and has several advantages over traditional methods. Rather than 10 to 12 mounting tabs with slots machined out internally for bobbins, there are 20 smaller mounting tabs that function as slots themselves. Instead of a steel bobbin providing float at each mounting point, it is accomplished with iron tabs that mesh seamlessly around the disc with the corresponding aluminum tabs of the hat. In this manner, the entire disc assembly is both simplified and strengthened.\r\n\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/spline_drive_close_up_1200.jpg\"\u003e\u003c\/u\u003e\u003c\/strong\u003e\r\n\u003c\/p\u003e\u003cp\u003eOur Spline Drive system eliminates the need for any type of bobbin, while also dispersing stresses across twice as many locations on the disc. The interlocking tabs not only provide the necessary room for radial float as the disc heats and expands, but also act as splines to directly transfer the torque under braking.\r\n\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003cu\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/spline_drive_disc_revised_arrows_1200.jpg\"\u003e\u003cspan class=\"redactor-invisible-space\"\u003e\u003c\/span\u003e\u003c\/u\u003e\u003c\/strong\u003e\r\n\u003c\/p\u003e\u003cp\u003eWith the tabs handling load transfer, the fastener portion of the new Spline Drive assembly is quite different and much simpler. On a traditional float-in-disc design (below), each of the 10 to 12 load-bearing fasteners is pulling double duty, and must be thick enough to transfer brake torque and hold everything together at the same time. \u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/bobbin_drive_disc_arrows_revised_1200.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eThe Spline Drive system eliminates half of the pieces found in a traditional bobbin drive hardware stack. Whereas our float-in-disc stack contains six pieces (below left), our Spline Drive setup requires only three: a bolt, retainer, and jet nut (below right). Since they are not load-bearing, the new fasteners are smaller in thickness at 5mm and don’t require as high of a torque value. Finally, when swapping to fresh replacement iron rings, only the jet nut must be replaced each time, reducing the cost of consumables.\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/bobbin_bolt_stack_vs_spline_drive.jpg\" alt=\"bobbin_bolt_stack_vs_spline_drive.jpg\"\u003e\r\n\u003c\/p\u003e\u003ch3\u003eTraditional Bobbin Drive Hardware Design:\u003c\/h3\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/boltstack_57.jpg\"\u003e\r\n\u003c\/p\u003e\u003ch3\u003eNew Spline Drive Hardware Design:\u003c\/h3\u003e\u003cp\u003e\u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/spline_drive_bolt_stack_labeled_rev2_1001.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eTo provide axial float that also mitigates knockback and offers consistent pedal effort, we've integrated float-control springs into several recesses in the aluminum hat. They are completely encapsulated once assembled, so there's less of a chance for these springs to be bent or damaged vs. traditional anti-knockback (AKB) spring clips. \u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cu\u003e\u003cu\u003e\u003cstrong\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/tooth_drive_disc_spring_fade_shot_cropped_1200.jpg\"\u003e\u003c\/strong\u003e\u003c\/u\u003e\u003c\/u\u003e\r\n\u003c\/p\u003e\u003cp\u003eAnother unique benefit of the Spline Drive system is an extremely low profile on the inside of the disc assembly, providing an undisturbed entry path for cooling air through the vanes (see below).\r\n\u003c\/p\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/spline_drive_disc_low_angle_1200.jpg\"\u003e\u003cp\u003e\u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003eFinally, the elegant hardware packaging provides an incredibly clean aesthetic when viewed from the outside. The only visible piece of hardware is the bolt head, and everything else is hidden inside the disc.\u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/spline_drive_981_disc_hat_outside_close_1200_rev.jpg\"\u003e\r\n\u003c\/p\u003e\u003ch3\u003eInternal Vane Quantity and Quality\u003c\/h3\u003e\u003cp\u003eThe\r\n internal vane design on AP J Hook Discs is quite a bit different vs. \r\nOEM-style discs and other brands of aftermarket discs. Many OEM discs \r\nfeature a pillar vane design, which can be thought of \r\nas a group of posts or pillars connecting the two disc halves together \r\n(see pic below). \r\n The pillars are not organized linearly from the outside to the inside \r\nof the disc, and turbulence is created as air flows through and among \r\nthem.  Pillar vane discs are therefore not particularly well suited to \r\nheat evacuation.   The goals of a pillar vane design are disc face \r\nstability for low NVH (noise, vibration, harshness), and a low cost of \r\nproduction.  Pillar vanes are non-directional, and the same part number \r\nis \r\nused on both sides of the car (again for cost reduction). Other OEM \r\ndiscs feature a straight, non-directional internal vane.  While that \r\ntype of vane flows more air than a pillar, it does not move nearly as \r\nmuch air as the directional vanes featured in AP Racing's discs.  Having\r\n directional vanes means that AP Racing discs are handed.  There is a \r\nunique left disc and a right disc in each pair, and they cannot be \r\nswapped from side-to-side on the car.  The orientation of the vanes is \r\noptimized to spin in a certain direction, pumping the maximum amount of \r\nair possible through the disc.  The shape of these internal vanes is \r\nalso optimized to promote smooth airflow.\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/left_right%20illustration_3.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/Disc_CutOut_three_quarter_view_WEB.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eIn\r\n addition to having a superior internal vane design, AP Racing discs \r\nhave far more of\r\n them!  Most aftermarket discs have 30 to 48 vanes. After extensive \r\nCFD and thermal stress analysis, AP designed the Competition J Hook's \r\nwith a high vane count (typically 60 to 84 depending on application).  \r\nHaving more vanes increases airspeed and heat transfer through the disc,\r\n reduces air recirculation between vanes, and reduces \r\ndeflection at the disc face.  Compared to an OEM-style disc or \r\ncompetitor's 48 vane discs, the 60+ vane discs are less prone to coning,\r\n distortion, and cracking, while \r\nproviding less brake fade, reduced judder, more even pad contact, and a \r\nlonger service life.\r\n\u003c\/p\u003e\u003cp\u003eBelow is a comparison of a one-piece OEM \r\npillar vane disc and an AP Racing two-piece J Hook.  A few things to \r\nnote in these pictures: The AP Racing disc has a much wider air gap \r\nbetween the disc faces, allowing considerably more airflow into and \r\nthrough the disc.  The uniform, directional vane design also contributes\r\n heavily to superior airflow.\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/OEM_disc_vane_design_WEB_cropped.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/jhook_disc_vane_design_web_cropped_2.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003eMost\r\n of the cooling air that enters a brake disc comes from the back side of\r\n the discs, particularly if brake ducts are being employed.  The top \r\ndisc is an OEM pillar vane.  The second disc is an OEM dual-cast disc \r\n(which is technically a two-piece disc).  The bottom disc is the AP \r\nRacing J Hook.  Which of these discs do you think will flow the most \r\nair?  While the OEM discs have narrow inlet port and\/or obstructions \r\nblocking the disc vanes, the AP Racing disc offers a clear path for \r\ncooling air to enter and flow through the disc.  The result is \r\nsignificantly cooler discs that are less prone to cracking and wear.\r\n\t\u003cbr\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/OEM_disc_vane_design_inlet_WEB_cropped.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/frdiscairgap_dualcast_cropped_2.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/Jhook_disc_vane_design_inlet_WEB_cropped.jpg\"\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cem\u003e\u003c\/em\u003e\r\n\u003c\/p\u003e\u003ch3\u003eExclusive AP Racing J Hook Slot Pattern \u003c\/h3\u003e\u003cp\u003eWhen\r\n you cut a slot or drill a hole in a disc you impact heat transfer. The \r\narea around the slot or hole acts as a cool spot when the disc heats up,\r\n which is not ideal. Ideally, heat is distributed uniformly around the \r\ndisc so it can be hit with the cooling air that is pumping through the \r\ndisc, radiate outwards away from the disc, etc.  Cool spots create \r\nstress risers and increase the likelihood of the disc cracking. They \r\nalso cause the face of the disc to distort unevenly, leading to uneven \r\npad deposits, vibration, and judder.\r\n\u003c\/p\u003e\u003cp\u003eThe OEM discs avoid this \r\nproblem by simply leaving the face blank.  While the risk for NVH goes \r\ndown, so does the pad bite and feel of the disc through the brake \r\npedal.  Competitive aftermarket offerings typically have straight slots,\r\n which tend to leave cool spots across the disc face between the slots.\r\n\t\u003cbr\u003e \u003cstrong\u003e\u003cbr\u003e \u003c\/strong\u003eDuring\r\n exhaustive R\u0026amp;D testing, AP's J Hook design was found to create a \r\nconstant pathway of evenly distorted material on the face of the disc.  \r\nThe hooks are spaced out as evenly as possible both around the \r\ncircumference of the disc, as well as from the inside edge (where the \r\nhat attaches) to outer edge, with a slight overlap to promote even heat \r\ndistribution\/distortion. In addition to reducing cracking, the even \r\nheating of the disc also helps provide an even transfer layer of pad \r\nmaterial on the disc when you bed them in.\r\n\t\u003cbr\u003e \u003cbr\u003e Additionally, the J \r\nHook slot pattern produces a greater number of leading edges for the \r\npads to bite into vs. a traditional curved slot pattern, and \r\nparticularly a plain-faced disc.  While this may lead to slightly more \r\nwhirring or scraping noises from the discs when applying the brakes, the\r\n benefits of more even heat distribution, less propensity to crack, \r\ncleaner pad material transfer during bed-in, and more bite far outweigh \r\nthe slight increase in NVH for the serious enthusiast.\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/jhook_two_web_3.jpg\"\u003e\r\n\u003c\/p\u003e\u003ch3\u003eFeature: Complex Metallurgy Developed Through 50+ Years of Experience \u003c\/h3\u003e\u003cp\u003eAP\r\n Racing has been designing brake components for more than 50 years.  \r\nThey've had their components on cars that have won more than 750 Formula\r\n 1 races!  On any given race weekend, AP J Hook discs can be \r\nfound on 75% or more of the NASCAR Sprint Cup grid.  AP has learned from\r\n these experiences, and have developed a proprietary iron alloy with \r\nextreme durability, designed specifically for what you intend to do with\r\n it (flog the hell out of it).  The primary objectives with OEM \r\ndiscs are simple: they must be cheap and easy to produce.  The design \r\nobjectives for these two products are vastly different.\r\n\u003c\/p\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/JHook_WEB.jpg\"\u003e\u003cp\u003e\r\n\t\u003cstrong\u003e\u003c\/strong\u003e\r\n\u003c\/p\u003e\u003ch3\u003eDisc Burnishing\/Bedding Service \u003c\/h3\u003e\u003cp\u003eIf\r\n your brake discs aren’t being properly prepared for abuse prior to \r\nflogging them on track, you’re exposing yourself to potential judder, \r\nvibration, and cracking issues.  We all know that prepping your pads and\r\n discs at the track can be difficult.  Doing so wastes time during the \r\nfirst session of the day, and it's a hassle and potentially dangerous \r\nfor other drivers as you go through the procedure.  Track time is \r\nexpensive and tough to come by. The more time you spend behind the wheel\r\n performing an elaborate bed-in procedure, the less time you’ll spend \r\ndoing hot laps.  Performing the procedure on-track also limits its \r\nrepeatability.  You can't control what's going on around you with track \r\nconditions, other drivers, etc., and many track configurations don't \r\nreally lend themselves to the constant start\/stop\/start required to do the\r\n job properly.\r\n\u003c\/p\u003e\u003cp\u003eEssex is now offering a solution via our \r\nprofessional burnishing service.  Previously reserved for our \r\nprofessional racing customers, we are now offering our retail customers \r\nthe option of having the discs in select Competition Brake Kits \r\npre-burnished at our factory.  We burnish thousands of discs for the top\r\n racing teams each year.  After countless hours of experimentation, and \r\nextensive feedback from the top drivers and teams, we can consistently \r\nsqueeze the most reliable performance out of AP Racing's discs.  The \r\nprocedure is incredibly repeatable, as it is performed on a \r\ncomputer-controlled machine by experienced technicians.\r\n\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003e\u003c\/strong\u003e The cost of our \r\nburnishing service is only $50 \r\nper disc, making it an affordable, time-saving option that will produce \r\nfar more consistent and safer results than trying the procedure on your \r\nown.\r\n\u003c\/p\u003e\u003cp\u003e\u003ca href=\"https:\/\/www.essexparts.com\/pro-race-services\/patented-brake-disc-bedding--burnishing\" target=\"_blank\" data-mce-href=\"http:\/\/www.essexparts.com\/professional-racing\/pro-services\/brake-burnishing.html\"\u003eWatch a brief video of our disc burnishing service here.\u003c\/a\u003e\r\n\u003c\/p\u003e\u003cp\u003e\u003cimg src=\"https:\/\/www.essexparts.com\/storage\/wysiwyg\/discs%20before%20and%20after%20burnish_2.jpg\"\u003e\r\n\u003c\/p\u003e\u003ch3\u003eReasonable Replacement Cost \u003c\/h3\u003e\u003cp\u003eLet's\r\n face it, no matter how good a brake disc is, it's still a consumable \r\nitem.  They're no different than brake pads or gasoline.  You beat them \r\nup until they crack to pieces, then you throw them away.  If replacement\r\n iron is too expensive, you're always driving in fear, waiting to shell \r\nout big bucks for a new set.  Despite having the most expansive set of \r\nfeatures on the market, \r\n\t\u003ca href=\"https:\/\/www.essexparts.com\/brake-discs\/ap-racing-competition-disc-replacement-rings\"\u003eour replacement iron rings\u003c\/a\u003e are completely affordable.\r\n\u003c\/p\u003e\u003cp\u003eGoing to the track is expensive!   \r\nEvent entrance fees, hotels, fuel, and tires all add up.  While you \r\nobviously want the best product available, you can't afford to pay a \r\nsmall fortune for something you're just going to destroy.  You can buy a\r\n cheap set of $150 discs for every event, have relentless heat issues, \r\nand find yourself constantly swapping them out.  When you do the math, \r\nthe long-term value of the AP J Hook's is tough to beat.  You'll enjoy \r\nall the benefits without breaking the bank, and you'll spend more time \r\ndriving and less time wrenching.\r\n\u003c\/p\u003e\u003cp\u003eElite level teams choose AP \r\nRacing discs because they know the work has been done to provide the \r\nbest available product at any price level.  The AP J Hook is a\r\n direct derivative of AP's vast racing experience.  You can buy with \r\nconfidence knowing that you're getting the best product available at any\r\n price point.  A note of caution however: the J Hook design is often \r\nimitated, and there are a number of lesser quality imitations on \r\nmarket.  Before purchasing, make sure you are getting an authentic AP \r\nRacing J Hook.\r\n\u003c\/p\u003e                                \u003cdiv id=\"pbed\" class=\"pdetail\"\u003e\n\u003cp\u003e\u003cstrong\u003e\u003c\/strong\u003eIf\r\n your brake discs aren’t being properly prepared for abuse prior to \r\nflogging them on track, you’re exposing yourself to potential judder, \r\nvibration, and cracking issues.  We all know that prepping your pads and\r\n discs at the track can be difficult.  Doing so wastes time during the \r\nfirst session of the day, and it's a hassle and potentially dangerous \r\nfor other drivers as you go through the procedure.  Track time is \r\nexpensive and tough to come by. The more time you spend behind the wheel\r\n performing an elaborate bed-in procedure, the less time you’ll spend \r\ndoing hot laps.  Performing the procedure on-track also limits its \r\nrepeatability.  You can't control what's going on around you with track \r\nconditions, other drivers, etc., and many track configurations don't \r\nreally lend themselves to the constant start\/stop\/start required to do the\r\n job properly.\r\n\u003c\/p\u003e\n\u003cp\u003eEssex is now offering a solution via our \r\nprofessional burnishing service.  Previously reserved for our \r\nprofessional racing customers, we are now offering our retail customers \r\nthe option of having the discs in select Competition Brake Kits \r\npre-burnished at our factory.  We burnish thousands of discs for the top\r\n racing teams each year.  After countless hours of experimentation, and \r\nextensive feedback from the top drivers and teams, we can consistently \r\nsqueeze the most reliable performance out of AP Racing's discs.  The \r\nprocedure is incredibly repeatable, as it is performed on a \r\ncomputer-controlled machine by experienced technicians.\r\n\t\u003cstrong\u003e\u003c\/strong\u003e  The cost of our burnishing service is $50 \r\nper disc ($100 per brake kit).\r\n\u003c\/p\u003e\n\u003cp\u003ePlease note that the \u003cem\u003epads\u003c\/em\u003e \r\nyou receive will not be pre-burnished.  In other words, the pads and \r\ndiscs do not have to be a matched set burnished together to reap the \r\nbenefits the procedure has on the discs.  In other words, we will \r\nburnish the discs in the pad compound you choose, they just won't be \r\nburnished with the exact set of pads that will arrive with your kit.\r\n\u003c\/p\u003e\n\u003cdiv class=\"video-container\"\u003e\r\n\t\u003ciframe src=\"https:\/\/www.essexparts.com\/\/www.youtube.com\/embed\/FG8Sg0jGKwQ\" allowfullscreen=\"\" frameborder=\"0\"\u003e\r\n\t\u003c\/iframe\u003e\r\n\u003c\/div\u003e\n\u003cp\u003e\u003cbr\u003e\r\n\u003c\/p\u003e\n\u003cp\u003eIf you'd rather have a go at preparing your discs yourself, please watch the video below:\r\n\u003c\/p\u003e\n\u003cdiv class=\"video-container\"\u003e\r\n\t\u003ciframe src=\"https:\/\/www.essexparts.com\/\/www.youtube.com\/embed\/pdPX6rzuINc\" allowfullscreen=\"\" frameborder=\"0\"\u003e\r\n\t\u003c\/iframe\u003e\r\n\u003c\/div\u003e\n\u003c\/div\u003e                                \u003cdiv id=\"psa\" class=\"pdetail\"\u003e\n\u003ch3\u003eDisc Attachment Hardware\u003c\/h3\u003e\n\u003cp\u003eTorque specs for this disc and hardware assembly=\u003cstrong\u003e 80 inch-lbs. (9 Nm)\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eReplacement hardware (not included with ring) -\u003cstrong\u003e \u003c\/strong\u003e\u003ca href=\"https:\/\/www.essexparts.com\/10bolt-spline-drive-floating-hat-disc-hardware-kit\" target=\"_blank\"\u003e\u003cstrong\u003e10-Bolt Spline Drive Floating Hat Disc Attachment Hardware Kit\u003c\/strong\u003e\u003c\/a\u003e\u003c\/p\u003e\n\u003cp\u003eIron Ring and Aluminum Hat Assembly Instructions\u003c\/p\u003e\n\u003c\/div\u003e                                \u003cdiv id=\"previews\" class=\"pdetail\"\u003e\n                    \u003ca href=\"https:\/\/www.essexparts.com\/review\/5054\" target=\"_blank\" class=\"btn ilb\"\u003eLeave a Review\u003c\/a\u003e\n                    \u003cdiv class=\"clear\"\u003e \u003c\/div\u003e\n\n                    \n                                    \u003c\/div\u003e\n                                        \u003c!-- end product details --\u003e\n    \u003c!-- end container --\u003e\n\u003c!-- end product additional --\u003e\n\n\u003cmeta name=\"_token\" content=\"KfewVSHLnK3dYH49FUc1OGZb8BTbP6JBThKGR7Ik\"\u003e\n\n\n    \n        \u003c!-- \/End Main Layout --\u003e\n                    \u003cdiv id=\"footer\"\u003e\n    \u003cdiv class=\"container\"\u003e\n        \n        \u003cdiv class=\"contact\"\u003e\n            \u003cdiv class=\"cms-block\"\u003e\n\u003cp\u003e\r\n\t125 Hampton Court\r\n\t\u003cbr\u003e\r\n\tCramerton, NC 28032\r\n\t\u003cbr\u003e\r\n\t\u003cstrong\u003eP:\u003c\/strong\u003e\u003ca onclick=\"ga('send', 'event', { eventCategory: 'general', eventAction: 'click', eventLabel: 'call', eventValue: 1});\" href=\"tel:704-824-6030\" value=\"+17048246030\" target=\"_blank\"\u003e704.824.6030\u003c\/a\u003e\r\n\t\u003cbr\u003e\r\n\t\u003ca href=\"tel:704-824-7300\" value=\"+17048247300\" target=\"_blank\"\u003e\u003c\/a\u003e\r\n\u003c\/p\u003e\n\u003cp\u003eApplication: Track\u003c\/p\u003e\n\u003cp\u003ePart number: 13.05.10068.\u003c\/p\u003e\n\u003cp\u003eConfirm fitment for your application before ordering.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e","brand":"AP Racing","offers":[{"title":"No Finishing","offer_id":53513474244890,"sku":"13.05.10068","price":699.0,"currency_code":"USD","in_stock":true},{"title":"Disc Burnishing - Ferodo Pad Compound","offer_id":53513474670874,"sku":"13.05.10068-4040","price":774.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0917\/5105\/5642\/files\/disc_cutout_three_quarter_view_web_5_5.jpg?v=1794996307","url":"https:\/\/race-centric.com\/products\/ap-racing-j-hook-competition-spline-drive-disc-replacement-ring-380x32mm-right-hand","provider":"Racecentric","version":"1.0","type":"link"}